Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is not supported at present. Please extend your EasyEDA usage duration and try again.
Editor Version×
Standard
1.Easy to use and quick to get started
2.The process supports design scales of 300 devices or 1000 pads
3.Supports simple circuit simulation
4.For students, teachers, creators
Profession
1.Brand new interactions and interfaces
2.Smooth support for design sizes of over 5,000 devices or 10,000 pads
3.More rigorous design constraints, more standardized processes
This is a jtag probe with high-speed usb, a small touch display and a memory card.
This is under development. Changes may be made.
### Design guidelines
- All SMD components.
- Low cost:
- jlcpcb "economy" pcb assembly
- all components on one side
- 1mm/40mil between components
- use jlcpcb basic and preferred components if possible
- Convenience: display, connectors, buttons all on the same side.
- Hardware has to be good from the beginning. Software can always be changed later.
## Hardware
- Artery (雅特力) [AT32F405RCT7](https://www.arterychip.com/en/product/AT32F405.jsp), 256 kbyte flash, 96 kbyte ram, 216MHz.
- 16 MByte QUAD SPI flash for XIP "execute in place" firmware
- 280x240 LCD display with capacitive touch
- ambient light sensor to set LCD brightness
- SD card, useful for storing firmware images and data logging.
- CAN bus, 1 Mbit/s
- DS3231 real-time clock with battery back-up, in order to have logfiles with meaningful timestamps, and to be able to set alarms to wake up the processor.
- One high speed USB, 480 Mbit/s
- One full speed USB, 12 MBit/s.
- logic translators for target logic levels below 3.3V
- I2C connector
The box is 3D printed in transparent resin SLA 8001, so the ambient light sensor is exposed to light.
For the prototypes the AT32F405RCT7 processor is soldered by hand.
## Software
As software I tentatively propose rt-thread, with [black magic probe](https://github.com/blackmagic-debug/blackmagic) and [free-dap](https://github.com/ataradov/free-dap) as an rt-thread package. (being developed)
## Attachments
- AT32_WorkBench.zip is the project in Artery "AT32 Work Bench"
- 3DShell_PCB2.zip is STL files for the project box
- Design_Files.zip is Gerber, BOM and Pick-and-Place files
Design Drawing
schematic diagram
(
1
/
)
PCB
(
1
/
)
The preview image was not generated, please save it again in the
editor.
Forked project will be set private in personal workspace. Do you continue?
Clone
Project
The Pro editor is about to be opened to save as. Do you want to continue?
private message
Send message to koendv
Delete
Comment
Are you sure to delete the comment?
Report
at32f405-tool
No Profile
Announcer: koendv
Creation time: 2024-04-08 18:36:29
Published time:
2024-05-17 08:04:35
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
Submitted successfully! The review result can be viewed in the personal
center, review notification.
Kind tips
Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is
not supported at present. Please extend your EasyEDA usage duration and try again.
Share
Project
Copy
Copy
Scan the QR code and open it on the mobile terminal