EasyEDA supports the design of PCBs up to 50cm 50cm however we suggest our customers try to limit the design to a PCB size of no larger than 45cm 45cm. We may have to charge more for PCB sizes greater than this because they are harder to fabricate and need a bigger box with more packaging to protect them in shipping.
- If the size is smaller than 2cm, you need to panelize them to big size, or we can't help you to do the E-test.
EasyEDA uses a group buy model, so the price is very low, but the minimum number of PCBs should be 5 pcs. So for example, if you need 2 pcs, you need to order 5 pcs and similarly, if you need 7 pcs you need to order 10 pcs.
EasyEDA PCB provides 0.4mm, 0.6mm, 0.8mm, 1.0mm, 1.2mm, 1.6mm, 2.0mm thickness to choose from. If you need a 2.5mm or 3mm thickness board, please ask us for a quote via email. Please note that not all thicknesses will be available for all numbers of layers; for example no PCB house can fabricate a 32 layer PCB with a 0.4mm thickness!
For other numbers of layers or for a different layer stack up, please email us before placing your order.
You can select 1oz, 2oz in our order page.
For 1Oz, the track width and clearance can be 3mil.
- For 2Oz, please make sure the clearance is bigger than 8mil.
Some customers would like to merge more than 1 PCB in the same Gerber. We know you want to save money but this may make it hard to cut the board outline and more importantly this will take a lot more time to pick up and package the PCB. Although by ,doing this, you just have the one order, this complicates the fabrication of the panel and separation of the individual PCBs, so we will usually charge more for this. Similarly, using holes or slots as break off sections between boards are treated the same way as putting more than one design on a panel, each with its' own board outline.
Note: This additional charge only applies if the PCBs on a panel are different. Boards such as in the left hand image below will not incur an additional charge because they are easy to pick up but boards such as in the right hand image would incur an additional charge.
If you are just in the prototype phase and want to save money, then you can use the following trick. Place your different designs all inside one overall board outline and use lines drawn in the silk layer to mark out the separate the PCBs. Then, when you receive the PCB, carefully cut them apart yourself (we recommend you do this before you assemble the PCBs!). Like the PCB shown below, the yellow lines are drawn in the silk layers showing how you can merge 3 different PCBs in one gerber without incurring any extra costs.
This will help you to build a PCB Array to save time by making it faster to solder the PCB in SMT.
The V-cut line should be the same as the outline of the Sub-PCB. That is to say, there is zero space between the sub-boards.
The PCB panel needs to be larger than 8 * 8cm.
The V-cut line must cross the whole panel or else the factory can't add a V-groove on the PCB because the milling cutter may destroy any sub-PCBs on the V-cut line. They also cannot stop part way across the panel. The V-cut lines shown below are not acceptable:
EasyEDA supports FR4-Standard Tg 140C, FR4-Tg 150C, FR4-High Tg 170C. The FR4 TG's lead time may be more than 6 days. 90% of EasyEDA orders use FR4-Standard. For more information about this, please check the FR4 Material pdf
0.3mm for mechanical drill, 0.2mm for the laser drill. To save money, please use a minimum drill diameter of 0.3mm.
The width of the ring around vias or pads should be wider than 6mil/0.15mm.
We support down to 4mil but to save money, please use 6mil.
Make sure the Grid filled size is bigger than 8mil/8mil ( track/space), if less than that, we will change it to 8mil/8mil .
We support 5% and 10% precision. Please add enough information about your impedance control requirements to help us to fabricate your PCB.
If you wish to built PCBs that plug directly into edge connectors, such as memory cards, please choose Gold Fingers as shown in the image below:
If you need to build some PCBs as shown in the image below, please choose Half-cut holes.
When your Gerber is for just one design and you need EasyEDA to help you to duplicate many copies onto one panel, you can use this option.
You can drag across the rectangles to select then click on the panel to set how many rows and columns as shown in the image below:
For this image, we will merge 10 small PCBs to 1 big panel. If you order 5 pcs, then we will send 5 big panels to you, each with 10 PCBs on it so you will end up with 50 small PCBs.
If you select the Edge Rails, we will add a 5mm board edge as shown in the image below:
This is 2 rows and 5 cols panel PCB.
- Make sure the single PCB size is bigger than 2cm x 2cm, or we will charge $20 for the v-cut cost. Small PCB is hard to v-cut.
- Make sure the board outline is simple, for complex board outlines, you need to panelize by yourself. Or you can pay us $15 to do that, we will send the panelized gerber to you to confirm.
A Stencil can help you to solder the PCB quickly. For efficient and reliable SMT assembly a Stencil is a must.
EasyEDA can provide the option of NON-FRAMEWORK (or frameless) and FRAMEWORK stencils.
The right hand image below shows a frameless stencil. Frameless stencils are cheaper and lower weight(0.2Kg) so they can help to reduce the shipping cost.
We can ship PCBs to any country. The shipping cost depends on the weight of the boards, country, and shipping method. Before you pay, you can see the shipping cost and select the shipping method. So you just need to add it to your cart and then you will see some options like in the image below:
EasyEDA allows you to order many different PCBs together, just add the PCB to cart one by one , at last to pay for together.
EasyEDA uses a group buy model to save the cost of production, for picking up your PCB easier, we need to add a very small string to your PCB, the string might be under some IC, and if you solder the PCB, the string will be hidden. If you don't like it, there are two ways.
Email us, we will fabricate your PCB in another way, but the cost will be higher.
- When you order, you can use https://easyeda.com/Doc/Tutorial/PCBOrderFAQ#Panel-by-EasyEDA and keep the edge, we will add the string at the dirty edge, so there is no string on your product PCB.