Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is not supported at present. Please extend your EasyEDA usage duration and try again.
Editor Version×
Standard
1.Easy to use and quick to get started
2.The process supports design scales of 300 devices or 1000 pads
3.Supports simple circuit simulation
4.For students, teachers, creators
Profession
1.Brand new interactions and interfaces
2.Smooth support for design sizes of over 5,000 devices or 10,000 pads
3.More rigorous design constraints, more standardized processes
4.For enterprises, more professional users
Ongoing
STD
DC Output Solid State Relay
License:
Mode:Editors' pick
3.6k
1
0
1
Update time:
2021-08-05 10:50:57
Creation time:
2016-01-28 03:50:56
Description
DC Output Solid State Relay 10Amps 60V DC (Optically Isolated Input)
This project has been designed around TLP250/352 which is Opto-Coupler IGBT/MOSFET Gate Driver from Toshiba and Mosfet IRFP260 from IR, This relay consists of optically isolated gate driver and low impedance Mosfet. The combination of low resistance and high load current handling capabilities make this Relay suitable for a variety of switching applications. These devices are ideally suited for controlling high voltage and current DC loads with solid state reliability while providing 3750V isolation from input to output.
A solid-state relay (SSR) is an electronic switching device that switches on or off when a small external voltage is applied across its control terminals. SSRs consist of a Opto-isolator which responds to an appropriate input (control signal), a solid-state electronic switching device which switches power to the load circuitry, and a coupling mechanism to enable the control signal to activate this switch without mechanical parts. This relay designed to switch DC Load up to 10Amps. It serves the same function as an electromechanical relay, but has no moving parts. Solid-state relays have fast switching speeds compared with electromechanical relays, and have no physical contacts to wear out. Input trigger voltage 3V to 9V DC (1.5V to 12 V with Transistor) and output load 10Amps and supply 12V to 60V DC (100V DC also Possible). Gate Driver required supply 12V to 18V DC. Heat sink required for peak load.
Note 1: Q2, R1, J2 Are Optional for Low Current Trigger Signal Input
Note2: J1 (VC-J) Close In Case of Load Supply and Logic Gate Supply are same 12V to 18V DC for single supply input operation
Note 3: Done use R4, D1 LED If Load Supply is higher than 24V DC
Note4: J3 for Cathode ground in case of single pulse input
Features
+V Supply 60V DC (100V DC Possible) For Load
VC Supply 12V – 18V DC for Opto-Coupler Gate Driver
J1 Jumper for Single Supply operations ( If the Load Supply is between 12V DC to 18V DC)
Load Current Up to 10Amps (Required large size Heat sink for High current Load)
Two Input Options: 1. Anode Cathode Input 2. Signal input through Transistor Base input
Input Trigger 3V to 9V DC-Anode and Cathode ( Alter Resistor Value for 24V DC Trigger Input )
Signal Input 1.5V to 12V DC at Transistor Base ( Alter Base Resister Value for Higher trigger input)
Isolation Voltage : 3750V ( Gate Driver)
Operation Input Frequency up to 50Khz ( Refer TLP352 Data Sheet for More info)
Connections Cathode 2. Anode 3. Low Current Signal in 4. VCC-12V-18V 5. GD-Ground+V & GD Load Supply 12V to 60V DC+V & DR Load ( DR-Drain: –Load & +V: + Load)Applications
Motor Controls
Robotics
Medical Equipment
Railroad/Traffic Controls
Consumer Appliances
Industrial control
Solenoid Controls
TEC Drivers
High Current LED drivers
Low Voltage Halogen Lamp Dimmers
LED Light Dimmers
Tesla Coil Drivers
Induction Cook top
Home Appliances
![enter image description here][1]
![enter image description here][2]
[1]: http://www.electronics-lab.com/wp-content/uploads/2016/01/DC_Solid_State_Relay_BOM.jpg
[2]: http://www.electronics-lab.com/wp-content/uploads/2016/01/DC_Solid_State_Relay_I052B.jpg
Forked project will be set private in personal workspace. Do you continue?
Clone
Project
The Pro editor is about to be opened to save as. Do you want to continue?
private message
Send message to gerrychen
Delete
Comment
Are you sure to delete the comment?
Report
DC Output Solid State Relay
No Profile
Announcer: GerryChen
Creation time: 2016-01-28 03:50:56
Published time:
2021-08-05 10:50:57
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
Submitted successfully! The review result can be viewed in the personal
center, review notification.
Kind tips
Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is
not supported at present. Please extend your EasyEDA usage duration and try again.
Share
Project
Copy
Copy
Scan the QR code and open it on the mobile terminal