| ID | Value | Qty. | Package | Components | Supplier | Manufacturer | Manufacturer Part | LCSC |
|---|---|---|---|---|---|---|---|---|
| 1 | FS312F-G | 1 | SOT-23-6 | U1 | LCSC | FORTUNE | DW01+G | C14213 |
| 2 | MICRO USB | 1 | MICRO-USB-1 | USB1 | LCSC | LCSC | MICRO USB 5S B | C10418 |
| 3 | Toggle Switch | 1 | SW5-2.0-8.8X4.4X4.7MM-90D | SW1 | 3P-2.0-90D-REINFORCE; | |||
| 4 | TP4056 | 1 | SOP-8_EP_150MIL | U2 | LCSC | TOPPOWER | TP4056 | C16581 |
| 5 | 1k | 3 | 0603 | R1,R3,R4 | ||||
| 6 | 22uF | 2 | 1812 | C1,C2 | LCSC | FH | 1812X226K250NT | C28504 |
| 7 | 10u | 1 | 0603 | C3 | ||||
| 8 | Red(0603) | 1 | LED-0603 | LEDR | LCSC | LCSC | KT-0603R | C2286 |
| 9 | 19-217/GHC-YR1S2/3T | 1 | LED-0603 | LEDG | LCSC | EVERLIGHT | 19-217/GHC-YR1S2/3T | C72043 |
| 10 | 7.5k | 1 | 0603 | R2 | ||||
| 11 | 5V | 1 | HDR-1X1/2.54 | 5V | LCSC | LCSC | Header-Male-2.54_1x1 | C81276 |
| 12 | FS8205 | 1 | SOT-23-6 | Q1 | LCSC | FORTUNE | FS8205 | C32254 |
| 13 | 2k | 2 | 0603 | R5,R7 | ||||
| 14 | BAT+ | 1 | HDR-1X1/2.54 | BAT+ | LCSC | LCSC | Header-Male-2.54_1x1 | C81276 |
| 15 | 100 | 1 | 0603 | R6 | ||||
| 16 | 0.1u | 1 | 0603 | C4 | ||||
| 17 | BAT- | 1 | HDR-1X1/2.54 | BAT- | LCSC | LCSC | Header-Male-2.54_1x1 | C81276 |
| 18 | GND | 1 | HDR-1X1/2.54 | GND | LCSC | LCSC | Header-Male-2.54_1x1 | C81276 |
| 19 | MT3608 | 1 | SOT-23-6 | U4 | LCSC | LCSC | MT3608 | C84817 |
| 20 | SS34 | 1 | SMA(DO-214AC) | D1 | LCSC | SS34 | C8678 | |
| 21 | 22uH | 1 | 7*7*4 | L2 | LCSC | LCSC | SMRH74-220MT | C27442 |
2. From local computer:
3. Drag and drop an image file here or in the editor
4. Paste image (screenshot) in the editor (only for Chrome)
Comments
Hello, It is a good project. I have couple of LiPo batteries and I use them on same way but not on one board :(.
I use TP4056 with protection board DW01A and I solve the problem for low voltage protection for LiPo with use of voltage divider on 100 ohms (R6) resistor on pin that read VCC.
I see this from one Russian blogger, he use diodes for voltage drop, but I thing why to not add one resistor to ground :).
I have an iPhone, and I have to create a voltage divider to charge it, will it work if i attach this part at the end with a usb port?:
@DocFilo How many volts does it need on the data pins