Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD 18V Battery Balancer Ni-Cd (Active (SMD)

License:

Mode: Editors' pick

  • 1.5k
  • 0
  • 0
Update time: 2017-02-25 06:12:46
Creation time: 2017-02-25 05:22:39
Description
![enter image description here][1] ![enter image description here][2] ![enter image description here][3] The voltage regulator: ICL7660 and ICL7660A. Description: Capacitor C1 is charged to a voltage, G1, for the half cycle when switches S1 and S3 are closed. (Note: Switches S2 and S4 are open during this half cycle.) During the second half cycle of operation, switches S2 and S4 are closed, with S1 and S3 open, thereby shifting capacitor C1 negatively by G1 volts. Charge is then transferred from C1 to G2. If the voltage at G2 greater than G1 on the capacitor C1 pumping energy from G2 to G1. Thereby aligning the voltage on G1 and G2. Do’s And Don’ts 1. Do not exceed maximum supply voltages. 2. Do not connect LV terminal to GROUND for supply voltages greater than 3.5V. 3. Do not short circuit the output to V+ supply for supply voltages above 5.5V for extended periods, however, transient conditions including start-up are okay. ![enter image description here][4] Регулятор напряжения: ICL7660 и ICL7660A. (SMD) Описание: Конденсатор C1 заряжается до напряжения, G1, за половину цикла когда переключатели S1 и S3 закрыты. (Примечание: Переключатели S2 и S4 открыты в течение этого полупериода.) Во втором половина цикла работы, переключатели S2 и S4 закрыты, а S1 и S3 открытые, тем самым Заряд передается от C1 до G2. Если напряжение на G2 больше, чем на G1 то конденсатор C1 перекачивает энергию от G2 к G1. Тем самым выравнивая напряжение между G1 и G2. Микросхема: ICL7660S в корпусе: 8 Ld SOIC (SOIC-8) потребляет очень мало энергии, меньше чем саморазряд Ni-Cd Аккумулятора. ( и имеет малые размеры) По этому, Схему устройства, можно поместить в корпус Аккумулятора (шуруповёрта). если есть место. И что нельзя делать: 1. Не превышать максимальное напряжение питания. - ICL7660 . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5V to 10.0V - ICL7660A . . . . . . . . . . . . . . . . . . . . . . . . . 1.5V to 12.0V 2. Не подключайте клемму LV к полигоном для питания напряжения больше 3.5V. !!!(Если, Вы решите подключить Аккумуляторы с большем напряжением, чем 1.2V (к примеру: 3.7V) то клемму LV (6 нага Микросхемы ICL7660) оставить не подкюченной) 3. Не допускайте короткого замыкания на выходе на V + питания для питания напряжение выше 5,5V в течение длительных периодов времени, однако, переходные условия, включая запуск в порядке. ![enter image description here][5] Разъем типа XH-7A, на 7 контактов (две шт.) и XH-3A, на 3 контактов, вывести наружу аккумулятора, для контроля напряжения на каждой банке (можно подключить пассивны балансир). Контроль можно осуществлять при помощи прибора: 1-8S Lipo индикатора. ![enter image description here][6] ![enter image description here][7] 1) Нужно между первой и второй ножками подать минус пять вольт. 2) Отключить звуковую сигнализацию по низкому напряжению (программно, сверху есть кнопка). И у Вас будет один вольтметр на семь аккумуляторов (опрос цикличный (по кругу)). ![enter image description here][8] [1]: /editor/20170223/58ae6a3757818.jpg [2]: /editor/20170222/58ad89ea07554.jpg [3]: /editor/20170218/58a75bcff0058.jpg [4]: /editor/20170218/58a75bcff0058.jpg [5]: /editor/20170223/58ae715e6046f.jpg [6]: /editor/20170223/58ae6aa8b5141.jpg [7]: /editor/20170223/58ae6abf3acbe.jpg [8]: /editor/20170223/58ae6ae16f8db.jpg
Design Drawing
schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
ID Name Designator Footprint Quantity Manufacturer Part Manufacturer Supplier LCSC
1 XH-7A P1,P2 XH-7A 2 XH-7A EasyEDA LCSC C10394
2 ICL7660S U1,U2,U3,U4,U6,U7,U8,U9,U10,U11,U5,U12,U13,U14 SOIC-8_150mil 14 ICL7660SCPAZ Intersil LCSC C13725
3 10uF C1,C2,C3,C4,C5,C6,C7,C8,C9,C10,C11,C12,C13,C14 0805 14 0805F475M500NT FH LCSC C67142
4 XH-3A P3 XH-3A 1 XH-3A EasyEDA LCSC C2316

Unfold

Project Attachments
Empty
Project Members
Target complaint
Related Projects
Change a batch
Loading...
Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn