Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD SparkFun Cellular Shield - MG2639

License:

Mode: Editors' pick

  • 1.2k
  • 0
  • 0
Update time: 2021-04-11 15:08:27
Creation time: 2016-07-15 02:56:26
Description
![enter image description here][1] ![enter image description here][2] **Description:** The MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls! That means you can send and receive text messages, or use it to remotely connect your Arduino to the Internet. To top it off, it has an integrated GPS receiver, to help it from getting lost. All the supporting circuitry is provided including translation from 2.8V of the module to a user selectable 3.3V or 5V. Depending on which state it’s in, the MG2639 module can be a relatively power-hungry device with a maximum current draw of the shield is around 350mA. It usually won’t pull that much, but may require around 260mA during phone calls or 80mA during network transmissions. Both the cellular and GPS functions of the MG2639 require an external antenna connected to the module. There are two U.FL connectors on the side of the chip – one labeled “GSM” the other “GPS.” Though the MG2639 is the key part of the SparkFun Cellular Shield one of the hardest parts in getting the shield to work is finding a suitable network and SIM card to run it on. Two great options for getting this set up is utilizing our contract-free T-Mobile 6-month Unlimited card or picking up a prepaid “burner” phone – like a Go phone – and swap the SIM card into the shield. The Shield Hookup Guide found in the Documents section below has plenty of great instructions on how to get your cellular shield working and provides you with example sketches to receive SMS text messages, set up GPRS/TCP functionality, creating a DIY cell phone, and remotely post environment data to our data service running Phant. **Note:** The SparkFun Cellular Shield requires a passive GPS antenna with a short lead attached. Unfortunately, we do not carry this type of antenna at this time. For more detail and Documents, Please visit: http://www.sparkfun.com/products/13120 [1]: /editor/20160717/578ba2a912f58.png [2]: /editor/20160717/578ba2b27b46b.png
Design Drawing
schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
ID Name Designator Footprint Quantity
1 0.1uF C8,C5,C7 C-0603 3
2 MG2639 U3 MG2639 1
3 10uF C9,C1 1210 2
4 SPX29302 U1 Q5-DD_SPX29300 1
5 RESET S2 TACTILE-SWITCH-SMD 1
6 SIMHOLDER JP4 SIMHOLDER 1
7 100uF C6 EIA7343 1
8 ARDUINO_R3_SHIELD JP3 UNO_R3_SHIELD_NOLABELS 1
9 MMBT2222A Q1 SOT-23 1
10 JUMPER-PAD-2-NC_BY_TRACE SJ4 PAD-JUMPER-2-NC_BY_TRACE_YES_SILK 1
11 12mm coincell BAT1 BATTCON_12MM 1
12 BOOT S1 TACTILE-SWITCH-SMD 1
13 1.0uF C4 C-0603 1
14 33pF C3,C2 C-0603 2
15 AUDIO JP5 1X07 1
16 0.1uF C10,C11 c-0603 2
17 GREEN D3 L-0603 1
18 RED D1 L-0603 1
19 VBAT1 SJ2 PAD-JUMPER-2-NC_BY_TRACE_YES_SILK 1
20 LiPo JP1 JST-2-PTH 1
21 USB JP9 1X05 1
22 BOOT SJ1 PAD-JUMPER-3-2OF3_NC_BY_TRACE_YES_SILK_FULL_BOX 1
23 JUMPER-PAD-3-2OF3_NC_BY_TRACE SJ6,SJ7,SJ5,SJ9,SJ10 PAD-JUMPER-3-2OF3_NC_BY_TRACE_YES_SILK_FULL_BOX 5
24 FTDI_BASIC JP8 FTDI_BASIC 1
25 TXB0104 U2 SO14 1
26 M02 JP2 1X02 1
27 TEST-POINT TP1,TP2,TP3 PAD.03X.05 3
28 FTDI_VCCIO SJ8 PAD-JUMPER-2-NO_YES_SILK 1
29 VBAT_EN SJ3 PAD-JUMPER-2-NO_YES_SILK 1
30 YELLOW D2 L-0603 1
31 FIDUCIAL FID1,FID2 FIDUCIAL-1X2 2
32 STAND-OFF STANDOFF1,STANDOFF2,STANDOFF3,STANDOFF4 STAND-OFF 4
33 10k R1,R6 3-0603 2
34 1k R2,R5,R7,R8,R9 3-0603 5
35 4.7k R3 3-0603 1
36 MISC JP6 HDR1X5 1
37 UART2 JP7 HDR1X2 1
38 2.2k R4 3-0603 1
39 22 R10,R11 3-0603 2

Unfold

Project Attachments
Empty
Project Members
Target complaint
Related Projects
Change a batch
Loading...
Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn