ATtiny85 dual core board - two ATtinys work together to control neopixels, receive and decode IR remote signals, analyze audio from the microphone and check ambient light intensity. The board integrates a buck converter as well as expansion headers for additional sensors, actuators and I²C devices.
USBasp - USB ISP/TPI programmer stick for Atmel AVR microcontrollers with 5V and 3.3V target voltage based on the design by Thomas Fischl. More information can be found at https://www.fischl.de/usbasp/. Windows users may need to install a driver. Of course this is not necessary for linux and mac users.
|TGTVCC|Close to power target device via ISP header|
Simple USB ISP programmer for Atmel AVR microcontrollers based on the ATtiny45/85. More information can be found at https://dicks.home.xs4all.nl/avr/usbtiny/. Windows users may need to install a driver: https://learn.adafruit.com/usbtinyisp/drivers. Of course this is not necessary for linux and mac users.
Simple USB ISP programmer for Atmel AVR microcontrollers. More information can be found at https://dicks.home.xs4all.nl/avr/usbtiny/. Windows users may need to install a driver: https://learn.adafruit.com/usbtinyisp/drivers. Of course this is not necessary for linux and mac users.
USB ISP programmer with buffer for Atmel AVR microcontrollers based on the design by ladyada. More information can be found at https://learn.adafruit.com/usbtinyisp. Windows users may need to install a driver: https://learn.adafruit.com/usbtinyisp/drivers. Of course this is not necessary for linux and mac users.
Tiny handheld gaming device with games by Daniel C (www.tinyjoypad.com).
Project Video: https://youtu.be/dF4XtVUN5mo
ATtiny controlled and LiPo battery powered MP3-Player using the DFPlayerMini-module featuring:
- Micro-SD-card slot,
- battery charging and protection circuit,
- battery level detection,
- OLED display,
- on/off switch,
- volume control,
- 3 push buttons to control the player.
You can directly connect a 3.7V LiPo battery and a 3W/4Ohm speaker to the board.
The firmware is written for the folder-p...
The ATtiny85 USB Phone Charge Guard controls and monitors the charging of phones and other devices. Voltage, current, power and energy are constantly measured via the INA219 and compared with the user limit values. It cuts off the power supply via a MOSFET when a condition selected by the user is reached. The user settings are saved in the EEPROM.
|RESET|Reset all values|...
UPDI programmer (jtag2updi) for the new tinyAVR 0- and 1-series microcontrollers based on ATmega8/88/168/328.
Project Video: https://youtu.be/OVSLsA9-gF0
More information and firmware: https://github.com/ElTangas/jtag2updi
Getting started with the new ATtiny chips: http://www.technoblogy.com/show?2OCH
Mini UPDI Programmer based on ATti...
TinyKnob is a rotary encoder with a USB interface based on the ATtiny45/85 and the V-USB software-only implementation of USB1.1 devices on AVR microcontrollers (https://www.obdev.at/products/vusb/index.html). The example code implements a volume control knob for PCs which works without installing any driver by acting like a generic HID device.
Stand-alone High Voltage Serial Programmer and Fuse Resetter for ATtiny 13/25/45/85.
Project Video: https://youtu.be/2Q7D2RwkOMg
This work is licensed under Creative Commons Attribution-ShareAlike 3.0 Unported License.
HV UPDI (High Voltage Unified Program and Debug Interface) programmer for the new tinyAVR 0- and 1-series microcontrollers built on ATmega8/88/168/328 based on the design and the firmware by Dlloydev (https://github.com/Dlloydev/jtag2updi). The HV UPDI programmer will enable you to use the additional configuration settings for the UPDI pin without the fear of getting locked out from the MCU. It fe...