This project is a small automatic cooling system for home theater rack. It supports 2 temperature sensors for different zones in the rack and 2 12V PWM fans (standard for PC case cooling).
There is a power switch connector for a switch mounted on the casing (will be designed and 3D printed later). A reset button is provided mostly for reprogramming purpose. There are 4 buttons for setting up temp...
AxH is an Italian Community of homebrewing passionates.
AxHTherm is a smart device born to help home brewers to take control of their fermentation chambers.
It allows to define temperature steps, temperature ramps, and gravity set points to guide your fermentations!
You don't have to be nearby your fermentation chamber anymore! With AxHTherm you can remotely manage your fermentations, and trac...
A fully featured board based on ESP8266 and MAX31855 probe for managing temperature of electric ovens either by on-off or by pid control. The board supports 2 independent temperature probes and up to 2 relais for heating output. All the user operation is performed by a CGI web user interface provided by ESP8266 webserver and can be called by any standard html client like a webpage, a mobile or tab...
PCB is used to control 3 typical CPU fans with mounted high-power LED chips according to temperature and tach sensors
Relays are used to power-off LED drivers in case of fan failure or overtemperature condition
![enter image description here][1]
![enter image description here][2]
**Description**: The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a tempe...
Aim : To design PIC16F877A based Temperature controller, LM35 as Temperature Sensor, A pot reference set point adjustment. LCD to display Current Temperature, Reference Temperature and status of the output.
Software : MPLAB IDE.
Code : Assembly language(under development...).
esp8266 with 1-wire ds18b20 temperature sensor and light dependant resistor. Serial connector for uploading new sketches. DIP-switch for managing flash or run mode. 5V input.
![enter image description here][1]
![enter image description here][2]
**Description**: This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emitting, the TMP006 Breakout can determine how hot or cold the object is.
The TMP006 Breako...
![enter image description here][1]
![enter image description here][2]
**Description**: This is an evaluation board for the MLX90614 IR Thermometer. The sensor is connected to an ATmega328 running at 3.3V with a STK500 (Arduino) 8MHz bootloader. Code can be loaded through the FTDI basic interface and the Arduino environment.
The MLX9061 sensor is a high precision, small size, single zone IR...
![enter image description here][1]
![enter image description here][2]
**Description**: This is a breakout board for the incredibly small TMP102 digital temperature sensor. The TMP102 is a digital sensor (I2C a.k.a. TWI), has a resolution of 0.0625°C, and is accurate up to 0.5°C. This is a very handy sensor that requires a very low-current.
Communication with the TMP102 is achieved through a...
## Arduino drive the temperature and humidity sensor DHT11 ##
Available as both a plain component or an Electronic Brick.
The photos Electronic Brick: Voltage,Signal, Ground
![dht11][1]
## 10k pullup resistor needed ##
Needs 4.7K to 10K pullup resistor from +5V to Signal pin. Connect to Arduino MEGA 2560 Digital pin 3, not Analog pin.: When the connecting cable is shorter than 20...
We use cookies to offer you a better experience. Detailed information on the use of cookies on this website is provided in our Privacy Policy. By using this site, you consent to the use of our cookies.