Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD ROBONOMICS_SLS_GATEWAY_V01

License: GPL 3.0

Mode: Editors' pick

  • 2k
  • 0
  • 9
Update time: 2023-12-26 09:14:12
Creation time: 2022-01-17 12:08:33
Description

Development kit SLS ZigBee gateway

Ссылка на скачивание прошивок ESP32-WROVER-B и RF-BM-2652P2

https://drive.google.com/drive/folders/1h_XRUVWM8f5BtzlPs-sxU6WpR_D1mZgC?usp=sharing

Для прошивки RF-BM-2652P2 потребуется программа https://www.ti.com/tool/download/FLASH-PROGRAMMER-2

Схема с прошивками полностью проверена и работают. 

Для прошивки модуля ESP32 установите на задней части печатной платы  переключатели 1 и 3 в положение вкл., остальные выкл. 

Для прошивки ZigBee модуля переведите переключатели 2, 4 и 7 в положение вкл., остальные выкл.

После прошивки всех модулей для перевода устройства в рабочий режим установите переключатели 5 и 6 в положение вкл. остальные выкл.

Для дальнейшей настройки зайдите во вкладку Settings->Hardware и пропишите следующие параметры:

Zigbee UART RX: 22

Zigbee UART TX: 23

Zigbee RST Pin: 18

Zigbee BSL Pin: 19

Service Button Pin: 33

PullUp (True)

Led Red (or addr): 21

Led Green: 5

Led Blue: 27

 

Link to download firmware ESP32-WROVER-B and RF-BM-2652P2

https://drive.google.com/drive/folders/1h_XRUVWM8f5BtzlPs-sxU6WpR_D1mZgC?usp=sharing

To flash RF-BM-2652P2 you will need the program https://www.ti.com/tool/download/FLASH-PROGRAMMER-2

The scheme with firmware is fully tested and working.

To flash the ESP32 module, set switches 1 and 3 on the back of the PCB to on, the rest off.

To flash the ZigBee module, turn switches 2, 4 and 7 to the on position, the rest are off.

After flashing all the modules to put the device into operation, set switches 5 and 6 to the on position. the rest are off.

For further settings, go to the Settings->Hardware tab and enter the following parameters:

Zigbee UART RX: 22

Zigbee UART TX: 23

Zigbee RST Pin: 18

Zigbee BSL Pin: 19

Service Button Pin: 33

PullUp (True)

Led Red (or addr): 21

Led Green: 5

Led Blue: 27

Design Drawing
schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
Project Attachments
Order File name Download times
1

ESP32_firmware.zip

9
2

CC2652P_RFS_20210320.zip

14
Project Members
Target complaint
Related Projects
Change a batch
Loading...
Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn