Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is not supported at present. Please extend your EasyEDA usage duration and try again.
Editor Version×
Standard
1.Easy to use and quick to get started
2.The process supports design scales of 300 devices or 1000 pads
3.Supports simple circuit simulation
4.For students, teachers, creators
Profession
1.Brand new interactions and interfaces
2.Smooth support for design sizes of over 30,000 devices or 100,000 pads
3.More rigorous design constraints, more standardized processes
2 layer board of 3.95x3.94 inches (100.23x100.00 mm).
truzzi ATX PSU Breakout Mini V1.0
All SMD parts are 0805 or bigger
C1, C3: 0.1uF 0805 SMD capacitors.
C2: 1uF 0805 SMD capacitor.
F1, F2, F3, F4, F5: 1812 SMD PTC resettable fuses. (Littelfuse ones should work just fine, I used Bourns instead which are a bit larger).
J1: 24-pin ATX connector. I bought mine from Sparkfun but RS also sells them.
JP1: 3-pin header (for voltmeter output)
JP2: 6-pin header (for breadboard output, fused)
LED1, LED2, LED3, LED4, LED5, LED6: 0805 SMDs, choose the color you want but make sure to use appropriate resistors. You may not want full brightness and sure you don’t want magic smoke.
R1, R2, R11, R12, R15: 3.3K ohm, 0805.
R3: 330 ohm, 0805 (value may change – double check LM317 voltages).
R16: 10k ohm, 0805.
R6: 9/10W power resistor, not needed in my case.
R14: 1.2k ohm, 0805.
T1, T2, T3, T4, T5, T6: binding posts with 4mm hole. You may want some red ones for the positive lines and a black one for GND.
U1: LM-317, through hole. There should be enough space for a heatsink.
U2: TPS2513 from Texas Instruments. If you don’t have them, look up the datasheet and solder appropriate resistors on D+ and D- pins of the USB ports.
X1, X2: USB female connectors, through hole.
2 layer board of 3.95x3.94 inches (100x100mm). $77.65 for three.
Order now. Download. Permalink.
Forked project will be set private in personal workspace. Do you continue?
Clone
Project
The Pro editor is about to be opened to save as. Do you want to continue?
private message
Send message to mayordr62
Delete
Comment
Are you sure to delete the comment?
Report
truzzi ATX PSU Breakout Mini V1.0 copy
No Profile
Announcer: necochan228
Creation time: 2019-02-24 09:49:38
Published time:
2023-12-29 10:17:07
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
Submitted successfully! The review result can be viewed in the personal
center, review notification.
Kind tips
Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is
not supported at present. Please extend your EasyEDA usage duration and try again.
Share
Project
Copy
Copy
Scan the QR code and open it on the mobile terminal