Search results for ATMEGA328 S

GS 28-S (Footprint/Package: DIP 28 300)

GS 28-S DIP 28 300

. Socket 28 pins 300 mils wide for ATmega328P-PU

Motion Detection_Standard

Motion Detection_Standard

ATMEGA328P-AU,Arduino,PIR,PDV,24V,12V,LMV321SQ3T2G,K3-1280S-F2,RECOM R-78E5.0-0.5,IRF540NSTRLPBF,Motion,Detection,Delay,LED,controller,nightlight,closet light,PCB,layout. . Motion detector using ATMEGA328P-AU. Brightness, time delay, ambient light control with sensitivity control, and fade ON/OFF sw...

BigTime Watch Kit (Open hardware)

BigTime Watch Kit (Open hardware)

...SpikenzieLabs' Solder:Time kit. The heart of the kit is the much venerated ATMega328 using a 32kHz clock-source to keep time. To check the time, just press the button on the side of the watch and it pops up on a 4-digit 7-segment LED display. Thanks to some low-level hackery, the ATMega is running a...

Arduino Pro Mini 328 - 5V/16MHz (Open hardware)

Arduino Pro Mini 328 - 5V/16MHz (Open hardware)

...ty to slap it with the OSHW logo. Dimensions: 0.7x1.3" (18x33mm) Features: ATmega328 running at 16MHz with external resonator (0.5% tolerance) 0.8mm Thin PCB USB connection off board Supports auto-reset 5V regulator Max 150mA output Over current protected Weighs less than 2 grams! DC input 5V up to ...

Arduino Pro Mini 328 - 5V/16MHz (Open hardware)

Arduino Pro Mini 328 - 5V/16MHz (Open hardware)

...ty to slap it with the OSHW logo. Dimensions: 0.7x1.3" (18x33mm) Features: ATmega328 running at 16MHz with external resonator (0.5% tolerance) 0.8mm Thin PCB USB connection off board Supports auto-reset 5V regulator Max 150mA output Over current protected Weighs less than 2 grams! DC input 5V up to ...

Arduino Pro Mini 328 - 3.3V/8MHz (Open hardware)

Arduino Pro Mini 328 - 3.3V/8MHz (Open hardware)

...ty to slap it with the OSHW logo. Dimensions: 0.7x1.3" (18x33mm) Features: ATmega328 running at 8MHz with external resonator (0.5% tolerance) Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc) 0.8mm Thin PCB USB connection off boa...

LilyPad Arduino USB - ATmega32U4 Board (Open hardware)

LilyPad Arduino USB - ATmega32U4 Board (Open hardware)

...pdated the Simple board to create the LilyPad USB by replacing the classic ATMega328 with the new ATMega32U4. Not only does that mean that it’s running a variation of the latest and greatest bootloader, but it also means no more FTDI Basic! The only extra piece of hardware you need to program the ...

CryptoCape (Open hardware)

CryptoCape (Open hardware)

... Elliptic Curve Digital Signature Algorithm (ECDSA). You will also find an ATmega328p and a large prototyping area available on the board. The ATmega is loaded with the Arduino Pro Mini 3.3V bootloader and has broken out most of the signals to surrounding pads. Each CryptoCape comes with pre-soldere...

SparkFun 9 Degrees of Freedom - Razor IMU

SparkFun 9 Degrees of Freedom - Razor IMU

...rtial measurement. The outputs of all sensors are processed by an on-board ATmega328 and output over a serial interface. This enables the 9DOF Razor to be used as a very powerful control mechanism for UAVs, autonomous vehicles and image stabilization systems. The board comes programmed with the 8MHz...

microSD Shield (Open hardware)

microSD Shield (Open hardware)

...face. The SCK, DI, and DO pins of the microSD socket are broken out to the ATmega168/328s standard SPI pins (digital 11-13), while the CS pin is broken out to Arduino’s D8 pin. If you decide to use one of the many open source FAT libraries (like FAT16 or SDFat) make sure to change the code to r...

Block for Intel® Edison - Arduino (Open hardware)

Block for Intel® Edison - Arduino (Open hardware)

...uino onto your Edison with the Arduino Block. This board features the same ATmega328P you’ll find on Arduino Uno’s, Pro’s, and Pro Mini’s. The 8-bit microcontroller workhorse is connected to the Edison via a selectable UART, so your Edison can interact with the Arduino over a serial interfac...

SparkFun Geiger Counter

SparkFun Geiger Counter

...mit to 100Hz! This USB powered SparkFun Geiger Counter is equipped with an ATMega328 that can be programmed in circuit using one of the programmers below. Simply plug the unit into USB (make sure you have FTDI drivers installed), open a terminal program to the correct COM port at 9600bps, and you wi...

MiP ProMini-Pack (Open hardware)

MiP ProMini-Pack (Open hardware)

...transmit pin), 6V (Raw battery power). Features: MiP Back Pack Form Factor ATmega328 Running @ 8MHz Expansion Socket Pre-Soldered Two Prototyping Areas Optional FTDI Connector Area DC Input 3.3V - 12V Max 150mA Output 3.3V Regulator Over Current Protected Analog Pins: 8 Digital I/Os: 14 GitHub (Desi...

LilyPad MP3 (Open hardware)

LilyPad MP3 (Open hardware)

...dd a microSD card and some speakers, and you’re ready to rock. Features: ATmega 328p microprocessor with Arduino bootloader (Pro 3.3V/8MHz) VS1053B MP3 (and many other formats) decoder chip TPA2016D2 stereo amplifier MCP73831 3.7V Lipo charger (preset to 500mA, rate can be changed if desired) Head...

RedBoard - Programmed with Arduino (Open hardware)

RedBoard - Programmed with Arduino (Open hardware)

...the related items below for a compatible wall-wart power supply. Features: ATmega328 microcontroller with Optiboot (UNO) Bootloader USB Programming Facilitated by the Ubiquitous FTDI FT231X Input voltage - 7-15V 0-5V outputs with 3.3V compatible inputs 14 Digital I/O Pins (6 PWM outputs) 6 Analog In...

你现在访问的是EasyEDA海外版,不推荐使用,我们已经建立访问速度更快的中国区数据中心 https://LCEDA.cn
如果你已经有EasyEDA账号,请使用谷歌浏览器访问 https://easyeda.com/applyForLceda 进行数据迁移到中国区数据中心。
有问题联系QQ 3001956291 不再提醒