Search results for inner layer 1

Convert 2 layer to 4 layer PCB

... layer board. I would like to now make this board a 4 layer board. The 2 inner layers will be ground planes only. When I try to add a fill I get error, "This layer is invisible". I have inner layer 1 and 2 set in layer settings. Is this possible to do? Am I missing a setting?. Click on the littl...

Fabrication Output says 6 layers but I have only 4

Hi created a PCB with top, bottom, top silk, bottom silk, inner 1 and inner 2. However when get to fabrication output it generates a 6 layers quote which gives around 164 USD, while the 4 layers is 32USD, when I correct n# of layers by myself. I would like to know if this is a bug and I can trust a...

4 layer board - how to?

How do I set the PCB to 4 layers? Are the 'Inner 1' and 'Inner 2' layers (Layers -> Layers Options Settings) for that? . Yes Check that options ![enter image description here][1] [1]: /editor/20170624/594dc6ad75c93.png. Thank you, Dillon! Have a nice day!.

About auto routing in specific layers

...4f9f.png. @dillon Thank you for your reply. Currently I have 4 layers, two inner layers are power plane and ground plane, respectively, and the top and bottom layers are signal layers. I only want the auto router to route on the top and bottom layers. But there is no option to designate it. I tried ...

Autorouter ignores inner power planes

The situation: A 4 layer board. Inner 1 has a GND copper pour for a ground plane. Inner 2 has a VCC copper pour for a power plane. I've wired in the power connections from the pins to the power planes with vias. If I autoroute with rip-up, it 'rips up' the copper pours and routes on the inner layers...

Internal layers became reordered after upload

...roblem..... I can confirm that there is something strange happening to the inner layer numbering. Also, when I uploaded the downloaded Gerber files generated from a 4 layer PCB from a project created in EasyEDA: The upload analysis results seem to be unhappy about some of the files generated by the ...

trace sizes

...om layer gives the equivalent of a 20mil track. You can also put copper on inner layers but: 1) inner copper weight may be lower than on outer layers; 2) traces on inner layers get hotter than on outer layers for the same trace resistance because they are enclosed by PCB material. Note that: You can...

Solder Mask

...hey are through hole components, and pads is set to ALL (four) layers. All inner connections are connected with them and my problem is this: I wanna hide pads copper area in top copper layer with solder mask, only the holes in pads are exposed in top copper layer. Pads are with PTH hole (Plating Thr...

How to create blind vias?

I have a 4-layer board where the inner planes are for power and ground. I want to connect the components to them using blind vias - however I have not found any information how to do that.. EasyEDA does not directly support the creation of blind vias but if you contact Support directly they may be a...

Inner PCB cutouts

Hello, I would like to have a routed out rectangle in the middle of my PCB while having the copper layer, and I can't seem to do that. How should I proceed ? add a bunch of holes in the area I want cut out ? The cut out area is 30x10mm inside a 110x130mm pcb, and the cutout is meant to have a fan sl...

PCB Design Editor - Tutorial

... If you plan to design a PCB with more than 2 layers, then you must tick Inner1 and Inner2 for a 4 layer PCB plus Inner3 and Inner4 for a 6 layer PCB. ![](images/image139.png) ## Layers Tool Active Layer: The colours of the layers in the **Layers Tool** are defined in the Layer Options Setti...

no tracks when exporting

...allow me to export layers other than the 4 that are listed ( not including inner layers) or are the individual layers only for in-house use. . Hi Herchamier, Welcome to EasyEDA. From your description I think the problem is that you have put your tracks on the Top Solder layer and the Bottom Solder...

Connecting tracks to copper area

...his. I am trying to connect a defined copper area (for power supply) in a inner layer with vias to the component on top layer but i am unable to. I have been trying to connect tracks to via on the layers, naming the copper area same as the net but those has not worked, i am still seeing the ratline...

Multi layer pads not connected

...and only works for 2 layers as there's no guarantee of solder taking to an inner layer pad.. This stuff might help... https://easyeda.com/andyfierman/Welcome_to_EasyEDA-31e1288f882e49e582699b8eb7fe9b1f. @andyfierman Thanks for the link, will check it out! I fixed the ones I have by soldering a "clam...

Multiples Inner board outline cut-out

...rea, the following message appears on the display: "EasyEDA does not allow inner board outlines cut-out, please use SOlidRegion or HOLE". The point is that I used the Board-Outiline layer to draw the intended traits; because previously, when I used the Top layer, when clicking on the previous PCB pr...

你现在访问的是EasyEDA海外版,不推荐使用,我们已经建立访问速度更快的中国区数据中心 https://LCEDA.cn
如果你已经有EasyEDA账号,请使用谷歌浏览器访问 https://easyeda.com/applyForLceda 进行数据迁移到中国区数据中心。
有问题联系QQ 3001956291 不再提醒