CERN Open Hardware License
And enhanced gotek to make it smaller and userfriendly.
ID | Name | Designator | Footprint | Quantity | BOM_Manufacturer Part |
---|---|---|---|---|---|
1 | 1x2 | P1,P6 | HDR-1X2/2.54 | 2 | 2.54-1*2PFemale |
2 | Header-Female-2.54_1x2 | P4 | HDR-1X2/2.54 | 1 | 2.54-1*2PFemale |
3 | EGDE 34 | P8 | 5.25-FLOPPY-34PIN-CARDEGDE | 1 | Header-Male-2.54_2x17 |
4 | Header-Male-2.54_2x17 | P3 | HDR-17X2/2.54 | 1 | Header-Male-2.54_2x17 |
5 | Header-Male-2.54_1x4 | H1 | DIP-1X4P-2.54MM-M | 1 | 210S-1*4P L=11.6MMGold-plated black |
6 | 1k | R29 | 0603 | 1 | ? |
7 | 4K7 | R13 | 0603 | 1 | ? |
8 | 22ohm | R12,R11 | 0603 | 2 | ? |
9 | Header-Male-2.54_1x3 | P7 | HDR-3X1/2.54 | 1 | Header2.54mm 1*3P |
10 | 8MHz | X1 | SMD-5032_2P | 1 | SMD-5032_2P 8M 20pf 30ppm |
11 | 1x5 | H2 | DIP-1X5P-2.54MM-M | 1 | 210S-1*5P L=11.6MMGold-plated black |
12 | Header-Male-2.54_1x5 | H3,H4 | DIP-1X5P-2.54MM-M | 2 | 210S-1*5P L=11.6MMGold-plated black |
13 | BUZZERHNB09A03 | BUZZER1 | DIP-BUZZER-9X5.5 | 1 | buzzerHNB09A03 |
14 | STM32F105RBT6 | U3 | LQFP-64_10X10X05P | 1 | STM32F105RBT6 |
15 | Header-Male-2.54_2x5 | P5 | HDR-5X2/2.54 | 1 | 2*5pHeaders Pins 2.54mm |
16 | AMS1117-3.3 | U2 | SOT-223 | 1 | AMS1117-3.3 |
17 | JUMPER-2 | JP3 | 1X02 | 1 | ? |
18 | 100nF | C5,C6,C12,C4,C3,C9,C10 | 0603 | 7 | ? |
19 | 1n1000V | C7 | C0805 | 1 | ? |
20 | 10uF | C8,C11 | 0603 | 2 | ? |
21 | 1u | C13 | 0603 | 1 | ? |
22 | JUMPER-3PTH | JP1 | 1X03 | 1 | ? |
23 | Push Button 6x6 | SW02,SW01 | MY PUSH BUTTON 6X6 90DEGREE | 2 | ? |
24 | Header-Female-2.54_2x13 | P2 | HDR-13X2/2.54 | 1 | 2×13Female header Straight line |
25 | A/FPaste board Aparagraph 10Four feet without curling ironLCPVinyl6.8 | USB1 | USB-M-27 | 1 | A/FPaste board Aparagraph 10Four feet without curling ironLCPVinyl6.8 |
26 | LED-3MM | L4 | LED-3MM/2.54 | 1 | 204-10SURD/S530-A3 |
27 | 15pF | C2,C1 | 0603 | 2 | ? |
28 | 74LS07 | U4 | SOIC14N | 1 | ? |
29 | 0603 | R8,R7,R6,R9 | 0603-ARV | 4 | ? |
Comments (10)
Hi
Which firware must uploaded on this firware?and how must do it?
Does stm32 has bootloder itself
Hi
Excuse me for my mistakes on words
Which firmware must upload on this hardware?and how must do it?
Does stm32 has bootloder itself
@mrdavoudi
Hi,
You upload the software the same way you do with Gotek drive.
https://cortexamigafloppydrive.wordpress.com/
https://github.com/keirf/FlashFloppy/wiki/Firmware-Programming
What value are the resistor packs used, it doesn't say so on the schematics.... Also what value is 1n1000v capacitor?
Hi,
The resistors are 1K.
The C7 is 1nF 1000V. It will remove any static dischanges when inserting into the USB port.
@sundbyk Thanks for the clarification, I have one more question, all the Rotary Encoders I see need 5v, however the pinheader on your board delivers 3.3v, would it not be better to route that pin to the 5 v instead of 3.3v?
Hi,
The rotary encoder does only have pullup resistors.
It is only used for to pull the signal high for the MCU with uses 3V3.
Ref:
https://github.com/keirf/FlashFloppy/wiki/Hardware-Mods#rotary-encoder
Hi
I build the board.
The microcontroller and ls07 get too hot when I connect it to usb and before it burn i diconnect from usb
Do yourself build and test the board?
The original gotek have 6 nfet transistor that you remove .
Hi. Which jumper should I close to program the stm32?
@Yavy
Jumper P6 need to be closed to get STM32 into bootloader for programming via serial.