Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD Infrared (IR) Remote

License:

Mode: Editors' pick

Cloned from Infrared (IR) Remote

  • 925
  • 0
  • 0
Update time: 2018-03-09 19:01:02
Creation time: 2018-03-09 19:01:01
Description
## Infrared (IR) Remote ## Here's the pinout for almost every 3-pin IR Receiver: ![IR REMOTE][1] (Above): a diagram of connecting the receiver to an Arduino. There are many different manufacturers of IR Receivers and some have different pinouts: ![IR Receivers][2] Image courtesy of Alberto Piganti. See: http://www.pighixxx.com/ There is also an easy-to-connect IR Receiver Electronic Brick like this (Down). It can be plugged into a Sensor Shield or YourDuinoRobo1 with a 3-pin cable. ![IR Brick][3] CONNECTION NOTE: The IR Remote Receiver Electronic Brick has 3 pins. From left to right they are: (G) Ground, (V) Voltage, (S) Signal. BUT the marking sometimes vary on the little circuit board. In this photo they are marked G-R-Y. The 3-pin cable in the photo has the typical color code: (G) Ground = Black, (V) Voltage = Red, (S) Signal = White. ![ IR Remote Receiver][4] IR-REMOTE LIBRARY: Note: The following library must be installed in your Arduino installation for this to work! https://github.com/shirriff/Arduino-IRremote Below is the IR Remote Control Kit connected to a YourARDUINO with a 3-pin cable. On the right is the detail of the way the IR Receiver is carefully plugged into Gnd and Vcc on the cable, and the Out pin is insulated with a piece stripped from another wire, the pins are cut off evenly, and Out is routed into the Signal (White) pin of the cable. The software below displays the button that was pressed. ![ir romote][5] Test Arduino Software Sketch for IR Infrared Remote Control [Other Versions below]

#include "IRremote.h"

/*-----( Declare Constants )-----*/
int receiver = 3; // pin 1 of IR receiver to Arduino digital pin 3

/*-----( Declare objects )-----*/
IRrecv irrecv(receiver);           // create instance of 'irrecv'
decode_results results;            // create instance of 'decode_results'
/*-----( Declare Variables )-----*/


void setup()   /*----( SETUP: RUNS ONCE )----*/
{
  Serial.begin(9600);
  Serial.println("IR Receiver Raw Data + Button Decode Test");
  irrecv.enableIRIn(); // Start the receiver

}/*--(end setup )---*/


void loop()   /*----( LOOP: RUNS CONSTANTLY )----*/
{
  if (irrecv.decode(&results)) // have we received an IR signal?

  {
//    Serial.println(results.value, HEX);  UN Comment to see raw values
    translateIR(); 
    irrecv.resume(); // receive the next value
  }  
}/* --(end main loop )-- */

/*-----( Declare User-written Functions )-----*/
void translateIR() // takes action based on IR code received

// describing Car MP3 IR codes 

{

  switch(results.value)

  {

  case 0xFFA25D:  
    Serial.println(" CH-            "); 
    break;

  case 0xFF629D:  
    Serial.println(" CH             "); 
    break;

  case 0xFFE21D:  
    Serial.println(" CH+            "); 
    break;

  case 0xFF22DD:  
    Serial.println(" PREV           "); 
    break;

  case 0xFF02FD:  
    Serial.println(" NEXT           "); 
    break;

  case 0xFFC23D:  
    Serial.println(" PLAY/PAUSE     "); 
    break;

  case 0xFFE01F:  
    Serial.println(" VOL-           "); 
    break;

  case 0xFFA857:  
    Serial.println(" VOL+           "); 
    break;

  case 0xFF906F:  
    Serial.println(" EQ             "); 
    break;

  case 0xFF6897:  
    Serial.println(" 0              "); 
    break;

  case 0xFF9867:  
    Serial.println(" 100+           "); 
    break;

  case 0xFFB04F:  
    Serial.println(" 200+           "); 
    break;

  case 0xFF30CF:  
    Serial.println(" 1              "); 
    break;

  case 0xFF18E7:  
    Serial.println(" 2              "); 
    break;

  case 0xFF7A85:  
    Serial.println(" 3              "); 
    break;

  case 0xFF10EF:  
    Serial.println(" 4              "); 
    break;

  case 0xFF38C7:  
    Serial.println(" 5              "); 
    break;

  case 0xFF5AA5:  
    Serial.println(" 6              "); 
    break;

  case 0xFF42BD:  
    Serial.println(" 7              "); 
    break;

  case 0xFF4AB5:  
    Serial.println(" 8              "); 
    break;

  case 0xFF52AD:  
    Serial.println(" 9              "); 
    break;

  default: 
    Serial.println(" other button   ");

  }

  delay(500);


} //END translateIR

If you use the IRrecvDemo Sketch (above) and count the 21 buttons from left to right and top to bottom, the codes received are these: (NOTE: Receiving "FFFFFFFF" means "repeat" if you hold the button down.) ![result][6] [1]: /editor/20160105/568bb29a45918.jpg [2]: /editor/20160105/568bb321b9b9a.jpg [3]: /editor/20160105/568bb3903f59b.JPG [4]: /editor/20160105/568bb3e55ca56.jpg [5]: /editor/20160105/568bb4a806608.JPG [6]: /editor/20160105/568bb578bfd9d.jpg
Design Drawing
schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
ID Name Designator Footprint Quantity
1 TSOP1738 U1 TSOP17XX 1
2 Arduino MEGA 2560 U2 DIP 1

Unfold

Project Attachments
Empty
Project Members
Related Projects
Change a batch
Loading...
Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn