Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is not supported at present. Please extend your EasyEDA usage duration and try again.
Editor Version×
Standard
1.Easy to use and quick to get started
2.The process supports design scales of 300 devices or 1000 pads
3.Supports simple circuit simulation
4.For students, teachers, creators
Profession
1.Brand new interactions and interfaces
2.Smooth support for design sizes of over 5,000 devices or 10,000 pads
3.More rigorous design constraints, more standardized processes
Demonstrating the LM319EE spice subcircuit model, developed for EasyEDA, and a modified ST subckt spice model of the LM119/LM219/LM319 open collector comparator with floating (uncommitted) output transistor emitter (output ground) connection.
Although LM319EE is a dedicated spice model for the LM319, it can easily be adapted to represent the LM119 and the LM219 devices, including any variations from the Fairchild, Linear Technology, ST and TI versions of the device.
Note that this subcircuit models only one comparator so two comparator symbols must be placed in a schematic to represent the whole physical LMx19 device.
A single dual comparator symbol has not yet been made.
To see more about the device models:
Super Menu > Miscellaneous > Netlist for Document > Spice
A simple demonstration circuit showing the LM319 spice model.
**LM319EE** is a behavioural macromodel of the LM319, unique to EasyEDA. It is based on ST and TI datasheet parameters but can be adapted to the Fairchild part.
The LM319EE subckt models the gain and propagation delay of the device. It also models input bias current, quiescent current and input voltage range behaviour.
The device effectively shuts down for supply voltages below 2.5V and draws excessive supply currents for supply voltages above Vabsmax (36V) and reverse supply connections.
I/O pins are clamped to ground and supply rails to model overrail I/O pin behaviour.
Input differential and common mode voltage and output pin overvoltage behaviours are modelled.
The temperature dependencies of internal device parameters such as reference voltage drift and bias current are not modelled.
Noise is not modelled.
Note that the **LM319EE** model can easily be adapted to represent a wide range of 6 pin comparators such as the LM111, LT1011 and similar devices.
The LM319EE model is itself, a modified version of the EasyEDA generic 6 pin open collector / open emitter output comparator model, **compOC6pEE**.
*For 5 pin open collector, open drain and push-pull (totem pole) output comparators please see the generic **compOC5pEE**, **compOD5pEE** and **compPP5pEE** models respectively.*
The **LMx19_6pST** spice model is a modified version of the standard ST LMx19 model which incorrectly ties the output transistor emitter to the negative rail forcing the device to appear as a 5 pin comparator.
The LMx19_6pST subcircuit model correctly represents the open emitter connection of the LM119/LM219 and LM319 family of comparators.
Forked project will be set private in personal workspace. Do you continue?
Clone
Project
The Pro editor is about to be opened to save as. Do you want to continue?
private message
Send message to thierry.tein
Delete
Comment
Are you sure to delete the comment?
Report
The EasyEDA LM319 spice models
No Profile
Announcer: Thierry Teinghouo
Creation time: 2018-03-10 01:23:37
Published time:
2018-03-10 01:23:38
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
Submitted successfully! The review result can be viewed in the personal
center, review notification.
Kind tips
Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is
not supported at present. Please extend your EasyEDA usage duration and try again.
Share
Project
Copy
Copy
Scan the QR code and open it on the mobile terminal