License

CC-BY-SA 3.0

Recommend Projects

FP6277 Power Bank 3A

4 months ago 352
  • Description
  • Documents
  • BOM
  • Attachments
  • Members
  • Comments

Description

1. Overview

Powerbank based on FP6277 boost converter with 5V and 3.3V output up to 3A. Choose a good 18650 Li-Ion battery with a low internal resistance which is capable of delivering up to 7A!

IMG_20200614_131700_x.jpgIMG_20200614_131738_x.jpg

2. Working Principle

For battery charging the TP4056 (U1) is used. The TP4056 is a complete constant-current/constant-voltage linear charger for single cell lithium-ion batteries. The charge voltage is fixed at 4.2V and the charge current (max 1000mA) can be programmed externally with a single resistor (R3). The TP4056 automatically terminates the charge cycle when the charge current drops to 1/10th the programmed value after the final float voltage is reached. Other features include current monitor, under voltage lockout and automatic recharge.

For the battery protection (overcharge, overdischarge, overcurrent and short circuit protection) the DW01A (U2) is used in combination with two FS8205 dual MOSFETs in parallel (Q1 + Q2). The DW01A is constantly measuring the voltage across the battery and the current flowing in (when charging) or coming out (when discharging). If something goes wrong it takes the battery out of the circuit by closing the MOSFETs which act like a switch between the negative side of the battery (B-) and ground. The overcurrent protection works by comparing the voltage drop across the MOSFET with the internal 150mV reference of the DW01A. As the RDS(on) of one FS8205 is around 2x25mOhm, the DW01A would close the MOSFET at 150mV/50mOhm = 3A if only one FS8205 were used. By using two FS8205 in parallel, the resistance is cut in half, so the DW01A shuts down at 150mV/25mOhm = 6A and one FS8205 must only handle half of the current (3A) which is well within its specs. In this way, up to 6 amps can flow from the battery into the boost converter with a maximum voltage drop of 150mV.

To step up the voltage to 5V the FP6277 low-cost synchronous boost converter is used (U3). Instead of a diode that is used in conventional boost converters, it switches a second built-in MOSFET in sync with the first via the PWM signal. This significantly increases efficiency and thus higher output currents are possible.

The UZ1085L low dropout voltage regulator (U4) provides a voltage of 3.3V with a current of up to 3A.

3. Performance

Parameter Value
Battery Charge Current max 1000 mA
Battery Discharge Current max 7000 mA
Continuous Output Current max 2500 mA
Peak Output Current max 3200 mA
Quiescent Current < 3 uA

PowerBank_eff_5V_x.pngPowerBank_eff_3V3_x.png

4. License

license.png

This work is licensed under Creative Commons Attribution-ShareAlike 3.0 Unported License. (http://creativecommons.org/licenses/by-sa/3.0/)

Documents

Power Bank 3A

PowerBank_v1.0

BOM

ID Name Designator Footprint Quantity
1 Connector VIN,5V_OUT,3V3_OUT,BAT HDR-1X2/2.54 4
2 3.3uH L1 IND-SMD_L7.8-W7.0_0630 1
3 22u C7,C8,C5,C4 0805 4
4 100u C6 1206 1
5 100n C1,C3 0805 2
6 10u C2 0805 1
7 UZ1085L-33-TN3-R U4 TO-252-2_L6.6-W6.1-P4.58-BR 1
8 18650 Holder U5 BH-18650-A 1
9 POWER OUT USB2 USB-2.0-A-F-90-JCJ-H9.36 1
10 POWER IN USB1 USB PWR CONNECTOR 1
11 Slide Switch PWR SLIDE SWITCH DPDT 1P2T 1
12 75k R7 0805 1
13 1k R4 0805 1
14 100R R5 0805 1
15 27k R6 0805 1
16 1k5 R2,R1 0805 2
17 10k R8 0805 1
18 1k2 R3 0805 1
19 DW01A U2 SOT-23-6 1
20 FP6277XR-G1 U3 SOP-8_EP_150MIL 1
21 CHRG LED2 LED-0805 1
22 FS8205 Q2,Q1 SOT-23-6 2
23 FULL LED1 LED-0805 1
24 TP4056 U1 SOP-8_EP_150MIL 1

Attachments

None
Success
The owner does not allow comments in this project now

Comments (0)

goToTop
你现在访问的是EasyEDA海外版,使用建立访问速度更快的国内版 https://lceda.cn(需要重新注册)
如果需要转移工程请在个人中心 - 工程 - 工程高级设置 - 下载工程,下载后在https://lceda.cn/editor 打开保存即可。
有问题联系QQ 3001956291 不再提醒
svg-battery svg-battery-wifi svg-books svg-more svg-paste svg-pencil svg-plant svg-ruler svg-share svg-user svg-logo-cn svg-double-arrow
We use cookies to offer you a better experience. Detailed information on the use of cookies on this website is provided in our Privacy Policy. By using this site, you consent to the use of our cookies.