The EasyEDA "Tesseract" DIY Guitar Practice Amplifier is an LM386 based low power amplifier designed to deliver up to about 500mW into an
8 Ohm speaker when run from a 9V battery.
**Tesseract can be heard on YouTube here:**
The design given here - which includes a complete PCB design and Bill of Materials - is highly flexible and allows the several options...
This is a simple arduino sheild that can run on it's own as an arduino uno once it's powered up using the power input. to upload a code, simply remove the **ATMEGA328p** from your reguar arduino board and place this sheild on top of it. Then plug ur arduino board and upload a code.If you want to burn the bootloader of ur ATMEGA328p chip, then udon't have to remove ur ATEGA38p chip from ur regular...
THIS WORKS AS A REGULAR ARDUINO. ALL U NEED TO DO IS SOLDER THE COMPONENTS AND UPLOAD THE CODE USING AN (FT232RL USB TO TTL CONVERTER) MODULE. IF U DONT HAVE IT THEN SEE COPY THIS LINK AND SEE IN GOOGLE,
The Arduino platform has become quite popular with people just starting out with electronics. It is an open-source hardware design, based on microcontroller board designs and provide sets of digital and analog I/O pins that can be interfaced to various expansion boards ("shields") and other circuits. The boards feature serial communications interfaces, including USB on some models, for loading pro...
This is a custom - Arduino uno - based circuit.
- Microcontroller: Atmel ATMega328p
- Bluetooth Module: Support HC-06 & HC-05
- Motor Driver IC: Two L293D (up to 4 DC motors or up to 2 stepper motors)
- Servo motor header
- 3 input/output pins (Can be used to connect LEDs or button SWs)
- Programmable header
- Reset button
This is a small pcb that is designed to be used on an electric go-kart to display a stopwatch, motor RPMs, and cart speed as well as record this data on an SD card with a time stamp for analysis. The project is Arduino based and is ran off of 7-59 VDC or directly from a 5V source through any of the 5V or VIN pins on the data logger shield (this is not a protected input). It is designed to have w...
DIY Hot Air Station using Arduino (ON/OFF Based Heat Controller).
Arduino Pro Mini for all the magic.
TM1637 4-Digit Display Module for display purposes.
LM358 based amplifier to read thermocouple voltages for measuring current temperature.
4 buttons to set the desired temperature required.
BTA16 with MOC3041 and other suitable passives as the heater controller.
Manual temperature calibration is n...
This afforable Geiger Counter that works as standalone device and also can connect to other external devices (like RaspberryPi/Arduino or other GPIO devices) to send the "clicks" thru GPIO interface.
The Arduino code for the Geiger counter is available here:
- Pin D2 --> Arduino interruption
- Pin D7 --> Buzzer
- Pin D8 -->...
# **DIY JBC 245 Controller (not tested yet)** #
Wich can be powered with a standart 19V DC laptop charger.
The project based on the Atmel328 μc, and i try makes simple as i can. The first problem driving a jbc tip is the thermocouple and the heater have a common pin and its not the GND. On some forum i found the easyest way to do is just siple pass the heater current on the thermocupple but thats...
•Канал на Ютуб / Channel on Youtube: https://www.youtube.com/channel/UCyVzmkYMe5pQK0HMWgyaE9Q?view_as=subscriber
•Видио на Ютуб / Vidio on Youtube: https://youtu.be/AejZOrpN9Ko
•Схема проекта / Project circuit: https://easyeda.com/romans.dodu/laser_spirograph_2019
•Архив с файлами лазерного спирографа ссылка / Archive with laser spirograph files link: https://drive.google.com/open?id=1GjJvR0MF...
# UM66T Melody Generator
An UM66T generates various Melody Tunes when triggered which can be used in car/scooter reverse signals, doorbells and toys.
**Order PCB:** [PCBWay](https://www.pcbway.com/project/shareproject/Musical_Bell.html)
## Electronic Components
| Qty | Comp...
**This is an experimental electronic circuit, without any warranty.**
Single channel 2-way 24 dB/oct Linkwitz-Riley active crossover.
Crossover frequency: 2.9kHz
PCB dimensions: 60mm x 100mm
Equalizer characteristics - simulation