Simple module for creating your own led lamp. You can use RGB strip, WS2812b, one-color strip or others.
![enter image description here]
In this project, we are going to use a PIC microcontroller to remotely control few AC loads by just using an IR remote. At the end of this project you will be able to toggle (ON/OFF) any AC load using an ordinary Remote from the comfort of your Chair/Bed. To make this project more interesting we have also enabled a feature to control the speed of the fan with the help of Triac. All these can be do...
This is a custom - Arduino uno - based circuit.
- Microcontroller: Atmel ATMega328p
- Bluetooth Module: Support HC-06 & HC-05
- Motor Driver IC: Two L293D (up to 4 DC motors or up to 2 stepper motors)
- Servo motor header
- 3 input/output pins (Can be used to connect LEDs or button SWs)
- Programmable header
- Reset button
Long story short, I decided to try out a **Cheapest PCB Prototype** -[JLCPCB]. Why I call “the Cheapest PCB Prototype .”Because i never experience so cheap price. Viewing the banner first time, I can’t believe the price :$2This is review is about only the **Cheapest PCB Prototype** service, so point one is that they support both modes.
**[Cheapest PCB Prototype] - JLCPCB Cost**
Cost was re...
This is a battery powered sensor board based on the ESP8266 (ESP-12F).
By using a TPL5111 chip the battery consumption can be reduced to about 1µA when the ESP is not enabled. When the TPL5111 chip receives 5V at it's wake up pin this will turn the ESP on by enabling the 3.3V voltage regulator. At this moment you can run any program you want. If you want to turn the ESP off again you have to drive...
ATtiny85 IR remote LED controller - mainly for ambient light behind a TV
Single colour LED
On first power up
Press PROG button to enter program mode
Programming can be over written once the PROG button is pressed
Press ON/OFF assigned button
LED fades in to set brightness value
Default to 50% 
Once the di...
Печатная плата для светомузыки (проект AlexGyver). В плате предусмотрено:кнопка управления (v1.0), микрофон, потенциометр (регулятор шумов), IR приемник для пульта управления, транзитный JACK 3.5, питание с PWR JACK, клеммника и просто 2PIN разьема, выбор питания (5V & 12V), выбор источника аудио (микрофон & JACK). Кстати: размер платы 30мм*48мм, а следовательно можно заказать аж 30 штук за 2$)) Е...
EN - This is a digital servo tester using a simple Attiny44 chip.
Code can be downloaded from http://bit.ly/2wBhLwt
(Also need software servo library found here https://playground.arduino.cc/ComponentLib/Servo/ and to program from Arduino need these boards https://github.com/SpenceKonde/ATTinyCore/blob/master/Installation.md)
more in this video https://youtu.be/8KIR4aokrsU
ES - Circuito programab...
EN - Used to program custom functions in it and be able to perform NAV lights, dual servo sequences, sensor triggered actions and similar simple tasks. It should be programmed with the Arduino IDE after installing the ATTiny Core in the board's manager - https://github.com/SpenceKonde/ATTinyCore ...For easy programming use the Uno shield found here https://easyeda.com/Joyvel/programing-for-attiny-...
One of the key concepts in electronics is the printed circuit board or PCB. It's so fundamental that people often forget to explain what a PCB is.
#What is a Printed Circuit Board?#
A [printed circuit board (PCB)] is a plastic board made for connecting electronic components together. These are used in almost all computers and electronics today.
A printed circuit board (PCB) mechanicall...
I tried a new **quick turn PCB fabrication**:[JLCPCB ](https://jlcpcb.com/m ), Here is the review about JLCPCB. Since I still have some older versions of one of the boards, I could make a comparison with the two **quick turn PCB fabrication**. I decide to not mention which competitor I pitched JLCPCB against...
**Stun gun** is a device which generates high voltage at it’s output by taking low voltage as input. Concept of this device is based on High volt inverter. Here we are building this **Stun Gun circuit on PCB** and below you can find the required circuit diagram and PCB layouts to build this stun gun yourself.
For complete details about the circuit with instructions on how to design this circuit...