Recommend Projects

STM32F103 Minimum System Board

5 years ago 5881
  • Description
  • Documents
  • BOM
  • Attachments
  • Members
  • Comments


STM32F103 Minimum System Board

1 STM32 master chip introduction Powerful STM32 with STM32F103RCT6 chips, Following is the main parameters Nucleus: Cortex-M3 32-bit RISC; Frequency: 72MHz, 1.25 DMIPS / MHz; voltage: 2-3.6V; Package: LQFP64; I / O ports: 64; Storage resources: 256kB Flash, 48kB RAM (and easy to move UCGUI LWIP,.Occupy protocol packets with intensive resource ,can develop a more powerful program) Interface resources: 2xSPI, 5xUSART, 1xI2S, 2xI2C; 1xLCD, 1xSDIO, 1xUSB, 1xCAN; ADC: 3xAD (12 bit, 1us, sharing 16 channels), 2xDA (12-bit); Debugging Download: Support JTAG / SWD, support IAP.

2 the regulator chip Using AMS1117-3.3V chip ,make the voltage in 3.3v regulator voltage 3JTAG / SWD interface
Support Download and simulation debugging . 4 USB interface Power supply to the circuit board with protection diodes ,also have two high-capacity electrolytic capacitors ( power for external device stably) 5 MCU pin interface Leads to all pins, convenient to connect peripherals with I / O connections. 6 5V / 3.3V power input and output port Commonly used as the external power supply, or handle with user`s board. (Multiple sets of power) 7 4 screw positioning holes ( with copper cylinder) 8 a power switch (can quickly turn off the power such as a short circuit , as well as power supply for an external module ,more convenient) 9 the LED With Power-indicator light 10 the user LED Convenient to test I / O output or indicate situation of the program running. 11 reset button Easy for users to reset the chip program. 12 8M crystal Through the multiplier setting, make the main frequency is 72M. 13 32.768K crystal Can use for built-in RTC , or for calibration. 14 JTAG / SWD interface supports downloading and debugging. 1.USB interface can communicate with a PC. 2.USART1 interface Use USART1 to download program, or use USART1 to output system information, Then to observe. 3.MCU pin interface Leads to all pins, convenient to connect peripherals with I / O connections. 4.5V / 3.3V power supply input and output interfaces Commonly used as the external power supply, or handle with the user board PCB board size: 7.0cm * 5.0cm enter image description here


New 2Schematic Module




ID Name Designator Footprint Quantity
1 1u C1,C2,C3 C1 3
2 100k R1,R2 TRIM_POT_PTH 2
3 STM32F103RBT6 U1 LQFP-64N 1
4 Header 3 J4 HDR1X3 1
5 30pF C1,C2 C0805 2
6 Resistor R3,R37,R2,R25,R27,R26,R16,R17,R18,R19,R36 R0805 11
7 104 C8,C9,C22,C4,C5,C7,C10,C12 C0805 8
8 SW-PB RST1 TD-19XA 1
9 Header 16X2 JP3 HDR2X16 1
10 TFT JP4 HDR2X16 1
11 Header 3X2 JP1 HDR2X3 1
12 LED D2,D1 0805D 2
13 ASM1117 U2 SOT-223 1
14 Header 10X2 JTG HDR2X10 1
15 Mini_USB J1 Mini_USB 1
16 Capacitor C20,C21 47uF_25V 2
17 Inductor L1,L2 C0805 2
18 Xtal Y1 CRYSTAL 1
19 Capacitor C11 C0805 1
20 5.8*5.8MM 自锁开关 六脚 P1 5.8*5.8MM 自锁开关 六脚 1




The owner does not allow comments in this project now

Comments (1)

MrIronFox Reply

в плате короткое замыкание под корпусом 1117 3.3V

如果需要转移工程请在个人中心 - 工程 - 工程高级设置 - 下载工程,下载后在 打开保存即可。
有问题联系QQ 3001956291 不再提醒
svg-battery svg-battery-wifi svg-books svg-more svg-paste svg-pencil svg-plant svg-ruler svg-share svg-user svg-logo-cn svg-double-arrow
We use cookies to offer you a better experience. Detailed information on the use of cookies on this website is provided in our Privacy Policy. By using this site, you consent to the use of our cookies.