New Pick and Place / Assembly ordering process does not show Basic/Extended
144 7
EdHayes3 3 months ago
The new (over the last month or so) process for ordering pick and place/ SMT/ Assembly service does not show the basic/extended designation on parts. Can that be fixed? I couldn't tell which part was causing an extended $3 fee. Finally figured it out, but it should show that fee on the line that is causing it, or at least the Basic/Extended designation. Thanks!
Comments
JLCPCBsupport 3 months ago
Hi, The below are about **“Basic components” and “Extended components” :** When a part from the Extended Components Library is used, the operator needs to mount the feeders manually, which increases the labor cost, we charge $3 per extended component. Basic components are those frequently used parts like chip resistors, chip capacitors etc. They have already been loaded on P&P machines and occupy the same feeder, so the operator don't need to keep swapping them in and out, thus there's no labor cost. The more , please visit : [https://support.jlcpcb.com/article/83-smt-assembly-faqs](https://support.jlcpcb.com/article/83-smt-assembly-faqs)
Reply
andyfierman 3 months ago
@JLCPCBsupport, The OP's question is not about the difference between Basic and Extended parts and why there is a cost difference. The question is why the process for ordering pick and place/ SMT/ Assembly service does not show the basic/extended designation on parts? In some cases it may be possible for a user to decide to replace an Extended part with a Basic part and so reduce the cost but if the basic/extended status of the parts are not clearly identified then it is difficult for the user to do this easily.
Reply
EdHayes3 3 months ago
@JLCPCBsupport, @andyfierman is correct. Here are screen shots which I'm referring to. At no point is it shown if a part is basic or extended. Item selection: ![Screen Shot 2021-06-19 at 6.46.08 PM, Jun 19.png](//image.easyeda.com/pullimage/CksVg6Wk2Jv8TLWlCBj2b7pT9IoxK984GLqGnxX5.png) Part info: ![Screen Shot 2021-06-19 at 6.52.38 PM, Jun 19.png](//image.easyeda.com/pullimage/ZWyml4njVKM8DtyNMG3Nvm7x3Gn1V5EbuBlv1Uxv.png) <br> Item validation: ![Screen Shot 2021-06-19 at 6.47.47 PM, Jun 19.png](//image.easyeda.com/pullimage/kbSpnEeOYCHWko8QO6FjvWaAu5lvd4nnuwGyxqxh.png)
Reply
JLCPCBsupport 3 months ago
Thanks for your guys advice .  This advice is helpful for us to perfect smt service.  I have made a feedback to our IT team . We will make a shown if a part is basic or extended.  :)
Reply
andyfierman 3 months ago
@JLCPCBsupport, Thanks.
Reply
EdHayes3 2 months ago
@JLCPCBsupport Thanks!
Reply
mwon 2 months ago
Hi, I was going to report the same issue, @JLCPCBsupport. Before this new version, the components were nicely ordered between basic and extended components. Such identification and division make the ordering process very easy, because I don't have to worry about the basic components (I almost always assemble them) and select which extended component I really want. Now, I need to check each component! It's a very slow process... :(
Reply
Login or Register to add a comment
goToTop
你现在访问的是EasyEDA海外版,使用建立访问速度更快的国内版 https://lceda.cn(需要重新注册)
如果需要转移工程请在个人中心 - 工程 - 工程高级设置 - 下载工程,下载后在https://lceda.cn/editor 打开保存即可。
有问题联系QQ 3001956291 不再提醒
svg-battery svg-battery-wifi svg-books svg-more svg-paste svg-pencil svg-plant svg-ruler svg-share svg-user svg-logo-cn svg-double-arrow
We use cookies to offer you a better experience. Detailed information on the use of cookies on this website is provided in our Privacy Policy. By using this site, you consent to the use of our cookies.