You need to use EasyEDA editor to create some projects before publishing
How can I create a customised connector as in JPG picture
897 14
Alibek 4 years ago
Hello, I'm creating a PCB with arduino pro mini Footprint that will communicate serially with an external device using only 2 signals, GND and 9V. The problem is that I cann't find out how to design on the PCB this interface as in Picture, Thanks for your help in advance.. Link to my project: [https://easyeda.com/alibekhbekh/lock](https://easyeda.com/alibekhbekh/lock) ![s-l1600.jpg](//image.easyeda.com/pullimage/gf2dzB4CQZmygDLcNF8jEGKNKrgtB4xRVrNgGgKG.jpeg) Regards
Comments
andyfierman 4 years ago
You have not said if this component is on the pcb or if it plugs into a socket on the pcb. You need to: 1. Find a datasheet for the part and for the socket it plugs into that shows the electrical connections and the dimensions or; 2. Create your own datasheet from your own measurements of the part. Then read (2.3) in (2) in: [https://easyeda.com/forum/topic/How-to-ask-for-help-and-get-an-answer-71b17a40d15442349eaecbfae083e46a](https://easyeda.com/forum/topic/How-to-ask-for-help-and-get-an-answer-71b17a40d15442349eaecbfae083e46a)
Reply
Alibek 4 years ago
Thanks for your kind replay. The socket is taken from the library for Arduino Pro Mini, this is not the isue .. My problem is how to design on the PCB the 4 contacts pins in the Picture... 4 copper long contacts for  gnd, 9v and Rx , Tx signals from/To Arduino pro mini sockets .. in my project I replace them by 4 buttons maybe I can fill them to create the long contact in picture.. Best regards
Reply
andyfierman 4 years ago
With no datasheet or other diagram or photos to show the overall structure of the part, it is not clear what or how it is intended to make contact with your PCB so it is not possible to advise how you create a suitable structure on your PCB. Please read: [https://easyeda.com/forum/topic/How-to-ask-for-help-and-get-an-answer-71b17a40d15442349eaecbfae083e46a](https://easyeda.com/forum/topic/How-to-ask-for-help-and-get-an-answer-71b17a40d15442349eaecbfae083e46a)
Reply
andyfierman 4 years ago
Got a part number?
Reply
Alibek 4 years ago
Unfortunately there is no product number, I am cloning this card with reverse engineering.. as you can see in the photo below .. the card must be inserted in that slot..the problem is how to create these 4 contacts on the PCB .. as you can see there is 4 rectangular holes and 4 tabs to make the contact with the slot when inserted .... ![2.jpg](//image.easyeda.com/pullimage/Jv9c5Vlr2eE142NyL2Djtw7zm8vHE71UHozWtL6A.png) Is there any solution for that? Thanks for your kind support
Reply
andyfierman 4 years ago
Some more photos from a number of different angles needed. I still have absolutely no idea what I'm looking at.
Reply
andyfierman 4 years ago
Is there a link to the original card?
Reply
Alibek 4 years ago
Thanks again. For sorry its a very old Card, I have it since more than 20 years ago...there is no any link... here is some photos inside, upper and lower side.. hope you can help me to find a solution. . any suggestion will be highly appreciated...All the eltronic part in photo are replaced by  Arduino. ![3.jpg](//image.easyeda.com/pullimage/dSxH6cvXifBTgo6VbWS6pV5jRn8vNobx0kDp0muf.png) ![1.jpg](//image.easyeda.com/pullimage/rwZpRpTrzKavVTy9MethIeOKebNhKuaZfmHKzX0r.png)![2.jpg](//image.easyeda.com/pullimage/2XhZmoJhVEYYk2n1MVcNb8FmVg7tkrQAzlJdHkDV.png)
Reply
andyfierman 4 years ago
Need side and non-component side views of: ![1.jpg](https://image.easyeda.com/pullimage/rwZpRpTrzKavVTy9MethIeOKebNhKuaZfmHKzX0r.png)
Reply
Alibek 4 years ago
Dear Andy, here is both sides... I will replace the plastic enclosure by the new PCB to have these 4 contacts inside the PCB itself... and the dimension of the PCB is same like the Plastic enclosure.. All electronic parts are replaced by one Arduino pro mini...... Thanks again for your support.. ![image.png](//image.easyeda.com/pullimage/88F7OLx7xTVNv9T2daBCgLLiVUIr9BUsSyYJ355N.png) ![image.png](//image.easyeda.com/pullimage/cavHh87PuLRX181iy3ovgv4pUaPFfl7bDJffTX3s.png) Best regards
Reply
andyfierman 4 years ago
Side view please to show the contact finger profiles...
Reply
Alibek 4 years ago
Hi, do mean this one : ![image.png](//image.easyeda.com/pullimage/l2mgxXSBfGKTQYSCKndFcwIxAawmf1eOCY3datGV.png) ![image.png](//image.easyeda.com/pullimage/dxkI66w3SdPeapxjPbU3pEzgty1WB5xFAIOn7daP.png)
Reply
andyfierman 4 years ago
OK, here's a little project to demonstrate what I suggest you try: [https://easyeda.com/andyfierman/lock-finger-contacts](https://easyeda.com/andyfierman/lock-finger-contacts) Google "phosphor bronze wire" for suppliers. You will have to make your own measurements to dimension the PCB, pads and pad spacings.
Reply
Alibek 4 years ago
This what I need.. I really appreciate... Thanks a lot for you kind and professional support..
Reply
Login or Register to add a comment
goToTop
你现在访问的是EasyEDA海外版,使用建立访问速度更快的国内版 https://lceda.cn(需要重新注册)
如果需要转移工程请在个人中心 - 工程 - 工程高级设置 - 下载工程,下载后在https://lceda.cn/editor 打开保存即可。
有问题联系QQ 3001956291 不再提醒
svg-battery svg-battery-wifi svg-books svg-more svg-paste svg-pencil svg-plant svg-ruler svg-share svg-user svg-logo-cn svg-double-arrow -mockplus- -mockplus- -mockplus- -mockplus- -mockplus- -mockplus- -mockplus- -mockplus-@1x -mockplus-

Cookie Notice

Our website uses essential cookies to help us ensure that it is working as expected, and uses optional analytics cookies to offer you a better browsing experience. To find out more, read our Cookie Notice